DIY Wooden Baby Pram or Stroller: Woodworking

Build DIY Wooden Pram or DIY Wooden Stroller which is perfect pram for your newborn. Give You Love ...

Build DIY Wooden Pram or DIY Wooden Stroller which is perfect pram for your newborn. Give You Love to your baby with your handmade wooden pram. I hope you will love and enjoy this easy wooden project to make a stroller for your baby or doll.

DIY Wooden Baby Pram or Stroller: Woodworking
 
DIY Wooden Baby Pram or Stroller


Things you need: 
4 - 5" rounds or store bought wheels and bolts
1 - sheet of 1/2" plywood @ 24" x 24" (available in project panel section of hardware store)
1 - 1x10 @ 36" long
1 - 1x2 @ 36" long
1 - 1" dowel @ 7-3/4" long
1 1/4 inch finish nails
1-1/4" Pocket Hole Screws
Elmer's Wood Glue
Elmer's Wood Filler
 
Tools:
Tape Measure  
Speed Square   
Pencil
Safety Glasses   
Ear Protection
Kreg Jig    
Drill
Jigsaw   
Miter Saw   
Brad Nailer  
Sander 

General Instructions: 

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always pre-drill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!

Dimensions: 
DIY Wooden Baby Pram or Stroller


Recommended for toddlers
 
Cut List: 
2 - 1/2" plywood @ 19-1/4" x 12" (sides of pram - will be cut out with jigsaw)
1 - 1x10 @ 9-3/4" - long point measurement, one end cut at 20 degrees off square (front of pram)
1 - 1x10 @ 5" - long point measurement, one end cut at 20 degrees off square (back of pram)
1 - 1x10 @ 13-3/8" - long point to long point measurement, both ends cut at 20 degrees off square, ends are NOT parallel (bottom of pram)
5" rounds or store bought wheels
2 - 1x2 @ 16" long
1 - 1" dowel cut at 7-3/4" long

Step 1: 
Transfer side pattern on to your 1/2" plywood.  Cut out with jigsaw.  Copy and create a second side.  Sand the two together so edges match.  Drill holes through both sides for the wheels at this step (sized for your hardware).


Step 2: 
Build the pram bottom and ends with 3/4" pocket holes on underside. 

Step 3: 
Attach sides to the bottom and ends with glue and finish nails. 

Step 4: 
Install wheels to sides through predrilled holes.
 
Step 5 Instructions: 
Use 1-1/4" screws to attach handle inside the pram, and attach dowel to the 1x2s.

Preparation Instructions: 
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.

DIY Wooden Baby Pram or Stroller: Woodworking


You are done! Enjoy.

You Might Also Like

0 comments

Follow by Email